全國服務熱線:021-57293980 51855511
 
中文 / ENGLISH   
首頁   |  關于我們  |  生產基地  |  新聞中心  |  技術中心  |  檢測中心  |  銷售中心  |  工作機會  |  聯系我們
 
關于我們
公司簡介
企業文化
公司理念
輝煌歷程
主要榮譽
工作機會
檢測中心
聯系我們
聯系我們
     
 

上海基地:

上海熱處理廠有限公司(總部)

全國免費服務熱線:

13371811158

聯系人:尚偉

Tel:+86(0)21 5729 3980

    +86(0)21 5185 5511

Fax:+86(0)21 5729 1585

Mail:info@shrcl.com

Add:上海市金山區金山衛鎮漕廊公路6033號(金石公路口)

Zip:201515

上海熱處理廠有限公司天津分公司

天津上熱真空熱處理有限公司

Add:天津市寶坻區黃莊鎮產業功能區一號路9號

聯系人:

左孝進  Mb:13821357588

Mail:xiaojin.zuo@shrcl.com

王思斌  Mb:18822112007

Mail:sibin.wang@shrcl.com

 

長沙上熱熱處理有限公司

聯系人譚秋云

Mb:15873146116 (n微信同號)

Mail:qiuyun.tan@shrcl.com

長沙工廠:湖南省瀏陽高新技術產業開發區西湖北路1號

湘潭工廠:湖南省湘潭市九華工業區九華大道9號

 

 
  您現在的位置:網站首頁-技術中心
 
氣體氮化和離子氮化之比較  2011/4/15 
 
分享到:
 
 

Gas Nitride or Plasma Nitride. Well known heat treat consultant David Pye, davidpye@pyemet.com is providing us with some details about what to consider when choosing between Gas or Plasma Nitriding. April 11/11

The choice between gas nitriding and plasma nitriding is usually a very difficult choice to make. The choice will come down to depend on;

  • Capital investment,

  • Logistics

  • Necessary surface metallurgy and control that is required for the processed component.

Capital Investment: The capital investment always seems to be considered as the driving force for the decision. Yes, the plasma systems are more costly than with the gas nitride. That is a correct assumption. But that seems to be where it stops. When making the cost comparison, between the two process techniques will generally be finished at the purchase price line. To have a true cost comparison, one really needs to consider the cost comparison of operating costs as well as the primary investment. It will then come down to considering the corporate amortization period of depreciation. After that, it really comes down to the operating costs. Once the equipment is amortized then it comes down to the direct operating costs of the equipment. It will be seen, that after the amortization period is complete, and then operating costs of the plasma technology are reduced, because of the nature of the process. This is because of process gas usage and power costs are lower. The writer has experienced the following approximate value to obtain a conventional nitrided case, as being;

  • 100ft³ of ammonia gas for 100ft² (approximate) of available surface area. (This is based on 5 to 7 process gas volume changes per hour). It further considers process temperature and time at process temperature. The reason for the process gas volume on gas nitriding being high is simply because the process vessel is being pressurized to a slight positive atmospheric pressure to act as a ‘sweep gas’ to ensure process gas circulation within the process retort and work.

  • 3 ft³ of process gas per hour (approximately)(nitrogen and hydrogen) for 100ft² work surface area. The reason for the low flow volume is because we are only using the gas necessary to generate the activity within plasma glow seam.

Logistics

The logistics consideration will be based on the;

  • Should the process be conducted ‘in house’ or sub-contracted out to a commercial heat treater, and why?

  • What is the distance of travel from the manufacturing house to the heat treatment shop?

  • Do we have the equipment to enable us to observe and control the surface metallurgy achievable. (Laboratory sample evaluation equipment)?

  • How quickly will the processed part  be processed by the commercial heat treater?

  • Do we have the appropriate floor space to accommodate the equipment?

  • Can we maintain and service the equipment?

Process evaluation

The question is now, how to test, evaluate, and most importantly, how do we control the process? A small metallurgical laboratory can be developed (or it is a  pre-existing laboratory) for the process evaluation that would include the following equipment;

  • Abrasive sample cut off saw

  • A pre-grind system for rough grind with silicon carbide papers

  • A rough polish using silicon carbide papers

  • Final polish using the appropriate grade of polishing cloth and either an aluminum slurry or diamond paste

  • Micro-hardness test unit

  • Inverted metallurgical microscope

  • Sample storage dessicator

  • Fume hood for simple acid etching

  • Spill kit

The above will enable you to process most metallurgical samples and not just nitride evaluation. The process control will come from the furnace control panel and its method of;

  • Data acquisition

  • Data storage

  • Gas delivery through either micrometer gas flow valves or mass flow controllers

  • Process gas  flow ratios

  • Temperature control

  • Time cycle control

  • Heating power control

The above is just some of control parameters that should be observed. Nitriding (gaseous or plasma) process parameters  need to be controlled if we are to produce continuous surface metallurgy and reproducible results.

 
 
日本亚洲AV,中国一级A做片免费观看,中文字幕无码在线,AV天堂中文字幕,一本之道高清在线观看